Steel-Bar-Cutter
steel-bar-straightening-cutting-machine
Steel-bar-bending-machine-at-Expo
lingwei-office

GQ40 Steel Bar Cutting Machine

Product: Steel Bar Cutting Machine
Model: GQ40 Rebar
Diameter: 4mm ~ 20mm
Max. Rebar Cutting No.: 6
Power: 2.2/3KW voltage, 380V
Speed: 2880r/min

Introduction

The steel bar cutting machine Model GQ40 is suitable for all kinds of carbon steel in reinforced concrete and hot-rolled round steel and rebar. GQ40 steel bar cutting machine can be also used to cut flat iron, square steel and angle steel.

Features

1. Small size, high quality, compact structure, reliable performance.

2. Good lubrication performance: it adopts box-type closed structure, gear splash lubrication, and it can continuous works more than 1 month after refueling. Notice: The oil level should not be lower than the oil scale line, so that the machine is always in good lubrication condition.

3. Less functional loss: due to the improved lubrication conditions, the gear shaft end adopts rolling bearings. Compared with the traditional steel bar cutting machine, the power can be reduced by 30%.

4. Easy to move: the front all-direction flexible wheels flexible, and easy to maintain.



Manual

(1) The feeding rebar shall be level with the lower part of the cutter. The length of the working table can be determined according to the length of the processed rebar.

(2) Before starting, check and confirm that the cutter has no cracks, the bolts of the cutter holder are tightened, and the protective cover is firm. Then turn the belt pulley by hand to check the gear meshing gap and adjust the cutter gap.

(3) After starting, test running firstly, and check that all transmission parts and bearings are running normally before operation.

(4) Do not cut the rebar if the machine does not reach the normal speed. When cutting the rebar, make the middle and lower parts of the cutter to cut the rebar, hold the steel bar and adjust the position then put it to the cutter quickly. The operator should stand on the side of the fixed cutter and press the steel bar forcefully to prevent the end of the steel bar from popping out and hurting people. It is strictly forbidden to hold the steel bar on both sides of the cutter with two hands leaning over to feed the material.

(5) It is not allowed to cut steel bars whose diameter and strength exceed those specified on the mechanical nameplate and red-hot steel bars. When cutting multiple steel bars at a time, the total cross-sectional area should be within the specified range.

(6) When cutting low-alloy steel, the high-hardness cutter should be replaced, and the cutting diameter should comply with the mechanical nameplate.

(7) When cutting short rebar, the distance between the hand and the cutter should be kept above 150mm. If the grip end is less than 400mm, the end of the steel bar should be pressed or clamped with a sleeve or clamp.

(8) During operation, it is strictly forbidden to directly remove broken ends and debris near the cutter by hand. Non-operators shall not stay around the cutter and the swing zone of the steel bar.

(9) When it is found that the machine is running abnormally, there is abnormal noise or the cutter is skewed, operator must shut down the machine immediately for maintenance.

(10) After the operation, the power should be cut off, the debris between the cutters should be removed with a steel brush, and the whole machine should be cleaned and lubricated.

(11) Before the hydraulic drive cutting machine starting, check and confirm that the hydraulic oil level and motor rotation direction meet the requirements. After starting, run it with no load, loosen the oil valve, and drain the air in the hydraulic cylinder before cutting the rebars.

(12) Before using the manual hydraulic cutting machine, the drain valve should be tightened in a clockwise direction, and it shall be loosened in a counterclockwise direction immediately after cutting. During operation, hold the cutting machine firmly by hand and wear insulating gloves.

Data Sheet

Steel Bar Diameter 6/40 mm (the steel bar tensile strength UB≦450mpa)
Flat Steel Size 70×15 mm
Square Steel Size 32×32 mm
Angle Steel Size 50×50 mm
Nominal Cutter Stroke 34 mm
Continuous Cutting 32 times/min
Motor Power 2.2/3KW voltage, 380V speed: 2880r/min
Dimensions 1250×500×730mm
Whole Machine Weight 485KG


Recommended number of bars to be cut at the same time

Diameter 6-8mm Cut 6 bars at the same time
Diameter 9-13mm Cut 5 bars at the same time
Diameter 4-18mm Cut 3 bars at the same time
Diameter 19-20mm Cut 2 bars at the same time
Diameter Above 20mm Cut 1 bar at the same time
GQ50-Steel-Bar-Cutting-Machine
Steel-bar-cutting-machine-gq40
GQ45-Steel-Bar-Cutting-Machine
office3
rebar-cutter-warehouseExhibition pictures(1)
Exhibition pictures(2) Exhibition pictures(3) expo
production
training
packing-case
product-delivery

INQUIRY

Please Feel free to give your inquiry in the form below.we will reply you in 24 hours.

  • *
  • *
  • *
  • *
Home Tel Mail Inquiry